Learnings
Learning from an early age…
My Grandfather who was a Tinsmith showed me how to solder when I was quite young. He also showed me how to cut metal and form it. By the time I went to Technical School in 1968 age 12, I was fairly conversant with handling sheet metal. We had a subject called Sheet Metal Practice. So when it became my turn to demonstrate how to solder in front of the teacher, it was one two three done ! The teacher was amazed and said “have you done this before?” I said “yes, my Grandfather showed me how to solder when I was 6”. The teacher said “well done” and moved on to the next student.
Hills Hoist Clothes Line…
We had the old style Hills Hoist clothes line in the family back yard. It has a geared crank set up to make it go up and down. The gears some how were damaged and my Dad bought some new parts to repair it. So here is my Dad with me at age 7 rebuilding the clothes line. I was of cource the assistant but can visually remember working with Dad and going through the steps of the repair. It worked ok after that for many years. Even after Mum and Dad moved from that home to another and it was still working well 20 years later.
Victor Lawn Mower Repair….
No sooner had Dad and I finished repairing the clothes line and we had to repair the lawn mower. It was the 1950s style Victor Mower, 125cc. It need a de-coke and new contact points. We had to remove the head to expose the piston, then scrape off the carbon build up on the the top of the piston so that it looked clean and tidy. The head was then fitted back on and also a new spark plug fitted.
Then we had to replace the points. The flywheel was removed and this showed the points. Had to remove those and fit the new ones. Now the tricky part. Dad showed and talked me through how to set the points so the spark would fire at the correct timing. Dad said that you bring the piston up to just before top dead centre and then adjust the points till they start to open. Then you will get the motor running and it will go ok. We fitted the fly wheel back on and then started the motor and it went very well. Mission accomplished.
Moving on to many years later, my Dad passed away and I did a talk about him at the funeral about our association and also setting up the points on the Victor Lawn Mower. I went through the story about how the points were set and then finalising that by saying, “ I always took this as a lesson in life. That if you get something close enough it will work well and get you through”. I then added, “ I really think Dad was only showing me how to set the points” the room of people cracked up with laughter. But in a way it is true and we need to learn as we go along.
My First Bicycle…
This was a Malvern Star that had been past down through the family. Think I was owner number three. I’m 8 years old. Dad and I rebuilt it and Dad hand painted the frame. Got it all sorted out and riding well. Along the way, I had to maintain it and keep it looking good. It taught me a lot about bearing adjustment, left hand threads, cotter pins and basically nuts and bolts.
The frame was way to big for me and I had the seat down as low as it would go but still managed to ride it and get around plus riding to primary school.
Towards the end of primary school I started racing bikes. So this old Malvern Star was my first race bike! It served me well up to the time when a car turned in front of me and I ran into it! I wasn’t too badly knocked around but the frame was bent so that was the end of that bike. The person who caused the crash paid my parents some money so I could buy another frame to rebuild the bike with many of the Malvern Star components. I was able to buy a much better frame made by Bates Bicycles. This frame was fairly current for it’s time. (Late 1960’s) It served me well for many years during the 1970’s. That bike is still with me in my collection of “my old racing bikes”. Likewise the old Malvern Star frame is still with me too.
Essendon Technical School…
After finishing primary school I moved onto secondary school and went to Essendon Tech. This was possibly one of the biggest revelations in my life ! A school full of machines, trade teachers and they produced young guys to start apprenticeships in all different trades. In the first year, we had Sheet Metal Practice, Woodwork ,Welding plus the normal Maths, Science, English and Art etc but the boys were engrossed with the machines. You could not wait to make something and learn all about it. We had a great time !
Towards the end of the second year we had a full on buzz going on about “ when we start third year we get to use a lathe, milling machine and other engineering machinery. So third year starts, it's the first week and we have Machine Shop Practice. We started at 8.30 in the morning, half an hour early so we could get through a whole morning of machining (actually it was more like fun!)
There was absolutely no one missing and we were lined up like good little boys waiting to go in. The teacher opens the door and we all pile in and in front of us is a room full of lathes and milling machines. It was incredible ! Also not forgetting we are all only 13 years old. So by the end of the lesson, we had all used a lathe and made something. The first model to make was a plum bob which I still have today.
So you can imagine how all these young guys were feeling at lunch time. It was certainly the beginning of working with machines and thoughts of what you wanted to be. The following two years were much more intense with learning and trade subjects. I followed on with the Machining side which covers mainly first and second year apprenticeships. We had some great teachers too. By the end of fifth year we were all getting pretty good at making things and certainly understood processes like screw cutting, indexing and general machining. By this time, most of us are 17 years old. I wanted to be a Fitter and Turner and specialise in Toolmaking. I did become this, thanks to the good old Tech School system. Thanks Techs !
This is a personal note. They changed and dissolved the Technical Schools in the late1980’s and took all the machinery away from secondly schools. Today there are no machines in secondary schools at all. We learnt from our time in the Tech Schools and had a great time as well. It also kept a lot of people out of getting into to trouble out on the streets. It was because we had focus and great mentors with the trade teachers.
My Apprenticeship Years…
Moving onto 1973. I managed to get an apprenticeship with Australian Controls. It was a hard place to get a job at and they did expect you to work and learn well. The product they made were temperature control thermostats for industrial refrigeration and control switches for washing machines. That is what they manufactured. They also made all their own tooling in house. These were mainly follow on press tools up to seven stage. They are like a jigsaw puzzle. All these press tools were made in the Toolroom by Toolmakers. This is what I wanted to be !
The guys in the Toolroom and the whole factory work force were a mixture of races mainly from Europe. We had Senior Toolmakers who sort of reminded you of your Grandfather. Always well dressed in clean grey dustcoats, shiny shoes, ties, cardigans and at the end of the day, looked like they were coming home from the drawing office. They were great mentors and instructors. Somehow they always put up with the young apprentices and even when we mucked up they didn’t get too upset with you.
I remember when they retired and there would be a morning tea for them and the boss would do a talk and hand them a present. After that these Senior Toolmakers would hand the young apprentices a present which was usually one of their old tools they had used for many years. I still have one of these items. It is a taper drift with his name on it. Thanks Harold, I will never forget you.
And Harold, I still use your taper drift !
My Uncle Jack…
My Mother’s brother was my Uncle Jack. Uncle Jack had gone to Essendon Tech, raced bicycles and became a Toolmaker. Obviously this was many years before my time. I wanted to be just like him ! As you have been reading, I did follow this line.
One very important thing I did learn from Uncle Jack was how to build a bicycle wheel. Uncle Jack was at my parents home for lunch one day and he asked me if I had done anything about rebuilding the damaged wheel on my bicycle. At that stage I had not done anything about it except purchase a new wheel rim and spokes. Anyway, Uncle Jack helped me after lunch to pull the wheel apart and rebuild it. I mainly did the work and he instructed me what to do. A couple of hours latter the wheel is back together ,nice and true and working well.
A few days later, one of my bicycle riding friends noticed the newly built wheel and asked “who did that?” I answered, “I did”. So the next thing you know I’m rebuilding and repairing wheels for my friends and their friends ! Little did I know at that stage, this would move onto my vocation and business in the future. This all happened back in 1968.
Uncle Jack also gave me a tool. His spoke spanner. I still have this too. Thanks Uncle Jack. You were a great mate and mentor.
Fred Chisholm…
I worked with Fred at Australian Controls while I spent time in the maintenance department during my apprenticeship. Fred was a very down to earth character and also made sure you learnt and would always answer any questions you had. Fred had been an ERA (Engine Room Artificer) in the Royal Australian Navy during WW2. In other words, a Fitter and Turner on board ship for repairs and maintenance.
On this particular occasion, the main boss at Australian Controls came in to the Maintenance workshop and goes troppo about a process machine that is not working on one of the production lines.
Fred answers, “we haven’t been told about this but will go down and sort it out”. The boss kept going a bit mad at all of us and then eventually left. Fred beckoned me to go with him. I was sort of Fred’s shadow and worked with him a lot during my stay there.
While we were heading down to look at the process machine, Fred said to me that he had already worked out what was wrong and we will have it fixed in five minutes and keep the boss happy. Fred was just like this, could make anything go and work well. A natural fixer.
However while walking along he told me a story that really did matter. During WW2 the ship that Fred was serving on had damaged one of its propeller shafts. At that time, they were in the Mediterranean when there was constant battle, ships being sunk, planes being shot down, mayhem and madness going on 24/7.
So Fred was in charge of the gang to get the repair done and get the ship up to speed so they could get back to port safely. The gang work feverishly. During that time, the head Lieutenant Commander came down into the engine room to see how the repair was going and when they could expect to get back up to speed. Lieutenant Commanders do not very often go down to the engine room to check on thing but on this occasion he did ! The main concern was that U boats were rampant in the area and there were constant enemy aircraft looking for situations to attack.
Fred obviously answered back that it would be a couple of hours until they had both screws working together and getting good speed to get out of harms way.
After a while the repair was done and everything worked well. The entire ship’s crew cheered and they were under way. They got back to port ok and safe.
Getting back to the point, Fred told me this story because the difference between things that really mattered and things that can be fixed easily with experience will always be the right thing to do. But it's not much fun being barked at because the person in charge does not really know what the problem is. I also learnt a lot from that story. Thanks Fred.
Another Fred Story…
During the mid 1970’s the Electricity Workers Union would go out on strike by shutting down electricity in areas around Melbourne without notice. So Australian Controls decided to fit in a large diesel engine and power generator to keep the factory going during the shut downs. I was involved with the installation along with Fred as his helper. We had to repair and rebuild this large eight cylinder in line engine and re-bearing the generator. The electrician installed the wiring and the change over switches looked like something out of an old horror movie. We got it up and running but had to do a test run every Monday morning.
To start this diesel engine up, it needed compressed air to crank it so there had to be a collector tank fed by a separate petrol run compressor to turn the big diesel over. The diesel crankshaft also had to be in a particular position so the compressed air could move it. The engine would turn over enough to make it start up. Then we went through the process of running the factory on the generator by shutting down the main electricity supply and switching it across to the diesel run generator. After a while, the process went in reverse and the factory was then running off the main electricity supply again. We did this for a number of weeks. Fred coached me to do the start up, running and shut down to the point were he would just stand there and watch me.
One Friday afternoon, Fred said to me that he was having a sicky on the following Monday and not to worry about running the generator. Monday comes along and around about 10am, the electricity goes off and the factory just stops ! I head straight to the diesel generator room and go into the process of starting it up and switching the electricity across. This took about ten minutes to get the factory back up and running. The deal then is that you stay there and keep an eye on temperatures and power outputs. This went on for a couple of hours then the main electricity was back and I had to go through the process in reverse and shut the diesel generator down. After that it was back to normal and hardly anyone knew what I had done. Fred came back to work the follow day and was told the story. He told me “well done, that’s what I would expect”.